Version as of 00:04, 29 Mar 2024

    to this version.

    Return to Version archive.

    View current version

    Vielen Dank für den Erwerb des Seneye Webservers (SWS)! Bitte lesen Sie die nachfolgenden Informationen aufmerksam durch, um Ihr Gerät ohne Probleme in Betrieb zu nehmen.

     

     
    BITTE VERBINDEN SIE IHREN SWS NICHT MIT DER SPANNUNGSVERSORGUNG ODER SCHALTEN SIE IHN EIN, BEVOR SIE DIE ANLEITUNG GELESEN HABEN.

    VERBINDEN SIE DEN SWS NICHT MIT DEM EDIMAX ADAPTER, BIS SIE DAZU AUFGEFORDERT WERDEN.

    SOLLTEN SIE GEBRAUCHTGERÄTE ERWORBEN HABEN, KONTAKTIEREN SIE UNS BITTE VOR DER INSTALLATION.

     

    Schritt 1 - Erstellen Sie Ihren Account auf seneye.me

    Wenn Sie bereits einen seneye Account erstellt haben, gehen Sie bitte direkt zu Schritt 2.

    Wenn noch keinen persönlichen Account auf seneye.me erstellt haben, beginnen Sie bitte mit der Registrierung. Sie müssen dazu eine Emailadresse angeben, auf welcher Sie Ihre Benachrichtigungen und Alarme erhalten möchten.

    Sobald Sie sich registriert haben, ignorieren Sie bitte die Hinweise in der Willkommensemail, welche Sie dazu auffordern, die seneye Software herunterzuladen. Als Nutzer eines Seneye Webservers (SWS) benötigen Sie keine zusätzliche Software auf Ihrem Computer - Ihr SWS erledigt alles für Sie! Sobald die Registrierung Ihres Accounts abgeschlossen ist, folgen Sie bitte weiterhin dieser Anleitung.

     

    Schritt 2 - Registrierung des SWS in Ihrem persönlichen Account

    Bitte gehen Sie auf die folgende Webseite, um den SWS mit Ihrem Account zu verbinden:

    http://my.sws.li

    Sie werden dort gebeten, Ihre registrierte Emailadresse, Ihr Passwort und die Angaben auf dem Aufkleber des Gerätes anzugeben. Sollten Sie den Aufkleber bereits versehentlich entsorgt haben, finden Sie die ID und PIN ebenfalls im Gerät, wenn Sie die rückseitige Abdeckung durch Drücken der beiden Verriegelungen öfnen. Ein Beispiel des Aufklebers auf der Verpackung sehen Sie hier:

    Bitte beachten Sie, das "O" ist der Buchstabe "O" und nicht die Zahl "0" im Feld ID!

    SWS front Sticker.jpg

    Schritt 3 - Verbinden Sie den SWS mit Ihrem Netzwerk (LAN)

    Sollten Sie in Ihrem Router kundenspezifische Einstellungen bezüglich Sicherheit, Kinderschutz oder Internetzugriff verändert haben, kann der SWS unter Umständen nicht mit der seneye Cloud kommunizieren. Bitte schauen Sie in diesem Fall hier für weitere Informationen.

    Tip: Wir empfehlen, daß Sie auch bei Erwerb einer WiFi Version die Installation zuerst mit einem Ethernetkabel und einer direkten Verbindung an Ihrem Router durchführen (ein Ethernetkabel ist im Lieferumfang enthalten). Dadurch ist eine sichere Verbindung und störungsfreie Installation des Gerätes gewährleistet. Sie können die Einrichtung des WiFi Moduls zu einem späteren Zeitpunkt durchführen. 

     

    Nachfolgend sehen Sie eine Übersicht der Anzeigen und Verbindungen des SWS. Sie benötigen diese Informationen im Verlauf der Installation.

    sws overview.JPG

    Um Ihren SWS an an Ihr Netzwerk (LAN) anzuschliessen, Verbinden Sie bitte ausschließlich die folgenden Anschlüsse:

    Hinweis: Bitte verbinden Sie zum jetzigen Zeitpunkt unter keinen Umständen Ihr seneye Gerät (REEF, POND o.ä.) mit dem SWS!

     

    A.       Verbindung zum Ethernet

    1.      Verbinden Sie das mitgelieferte Ethernetkabel direkt mit Ihrem Router.

    2.      Verbinden Sie das Ethernetkabel mit dem SWS (lila Buchse).

    sws connect ethernet.JPG

    B.       Verbindung der Spannungsversorgung

    1.      Stecken Sie das mitgelieferte Netzteil in eine Steckdose.

    2.      Verbinden Sie das mitgelieferte Mikro-USB Kabel mit dem Netzteil.

    3.      Verbinden Sie das Mikro-USB Kabel mit dem SWS (schwarze Buchse).

     

    sws connect ethernet and power.JPG

    Your SWS will now boot up:

    When you SWS boots, the lights on the front will flash in the following sequence:

     

    SWS-boot-up-led-sequence.gif

     

     

    Please leave the SWS connected unitl the following lights shown. If the lights flash in a circular sequence on the SWS after powering it up, it is downloading a firmware update. Please leave everything connected until the lights are in the state shown below.
     
    The 'power' and 'network connection' light should remain constantly illuminated.
     
    The "connection with the seneye servers" and "communicating with the servers" may flash dependent on the connection type - If they do not illuminate at all please have a look at the trouble-shooting link
     

    sws leds and glyphs trouble shooter.JPG

     

     

    Stage 4 - Find the SWS Graphic User Interface

    Edit section

    You can view direct data from your SWS by using PC, tablet or mobile phone that is connected to same Local Area Network (LAN) as the SWS. We would recomend doing this using FireFox as a browser, this renders the GUI of the SWS best.

    The SWS GUI can only be viewed on the LAN. If you are not on the network, the GUI will not be accessible.

    To find your SWS GUI please open up a browser on a device that is on your LAN. The following address needs to be entered the URL bar at the top of the browser. The URL is unique so your SWS and the part that is marked with **** on the address below needs to be replaced with the ID code that was on the label on the front of your SWS.

    HTTP://*******.sws.li

    An example is given below to show the format

    http://2mop534r4o6l.sws.li/

    SWS front Sticker.jpg

    If you cannot find your SWS GUI, then please contact us at [email protected]

     

    Stage 5 - Using the SWS GUI

    Once you have found the SWS, you will find a page like that below. The page is dynamic and you can move the tiles. It will also resize to any device screen size.

    Your SWS is now working. Don't forget to bookmark the page on your browser to access it easily.

     

    SWS beta interface.JPG

    Stage 6 - Connecting and updating your Seneye USB device

    Edit section

    Connect your seneye USB device (SUD) directly to the SWS. You will need to manually update the firmware in the SUD 

    Please note: your SUD will no longer communicate with the seneye connect on a PC after the firmware update

    You must connect the SUD directly to the SWS and not use any form of extenstion leads as the SUD will not communicate correctly.

    If you have purchased your SUD with a complete pack with the SWS then it will already be updated to the latest firmware. You will be able to tell if the SUD is already updated because it will show as connected on the SWS GUI.

    Once the SWS has detected that the firmware is out of date, it will put the SUD in boot load mode. You can tell that this has been completed because the 'seneye device connect light' on the SWS will be flashing.

    Please disconnect and re-connect the SUD from the SWS. 

    The tile that is circled below will indicate that the firmware is downloading. The lights on the SWS will flash in a circle to indicated this. 

     

    SWS SUD update interface 1.png

    Do not disconnect your SUD from the SWS until the tile show the image below and the LEDs on the front of the SWS are still circling

    SWS SUD update interface 2 DONE.png

    Once the tile above is shows, and the lights have stopped circling, disconnect the SUD from the SWS and reconnect it to complete the update.

    You will be able to see the update has been successful because the lights will illumiate. If the device is our of water, the lights on the front will flash as shown below:

    Please do not forget to register your seneye slide to get NH3 and pH readings!   Click here to learn how. 

    Edit section

    If you have any problems, please leave everything connected as it is and E-mail us at [email protected]

     

    SUD-V2-out-of-water.gif

    Setting up a WiFi module

    Edit section

    Now that your SWS is registered to your account and your SUD is connected, you can set up any adaptors that you are using for the connection. If your SWS came with a WiFi adaptor module, please refer to the instructions in the link below as to how to set this up (we recomend setting the WiFi plug up as a Wifi adaptor/WiFi Bridge).

    The Edimax instructions are here.

     

    SWS wi-fi and ethernet wiring diagram.png

     

    You may also find a the following links usefull to get the most from your new seneye device.

    The SWS Gui

    Adjusting your alert levels

    Use your light meter

    Seneye.me and your graphs